View CXA1390AQ_24027.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

CXA1390AQ/AR
S/H and AGC for CCD Camera
Description The CXA1390AQ/AR are CCD camera's signal processing ICs which extract signals from the CCD output. These bipolar ICs perform correlated double sampling. AGC, color separation, high luminance detection and others. Additionary, these ICs are not affected by irregular pulses which occure during the CCD shutter mode. Featuers * Pin compatible upgraded version of CXA1390Q/R which can be swapped out while using same peripheral chips * Almost completely corrects irregular pulses and their negative affects * Correlated double sampling function alllows for the suppression of low band noise in the CCD output * AGC amplifier, which has High S/N ratio and wide gain control range, enhances the camera sensitivity * Output for iris adjustment. High luminance detection output * Usage of Vg (regulator) output allows for the formation of IRIS and AGC LOOP which are not affected by supply voltage functation Operating Conditions Supply voltage VCC CXA1390AQ 48 pin QFP (Plastic) CXA1390AR 48 pin LQFP (Plastic)
Application S/H and AGC for CCD camera Structure Bipolar silicon monolithic IC Absolute Maximum Ratings (Ta = 25C) * Supply voltage VCC 12 V * Operating temperature Topr -20 to +75 C * Storage temperature Tstg -65 to +150 C * Allowable power dissipation PD 600 (QFP) mW 950 (VQFP) mW (40mm x 40mm, t = 0.8mm with a mounted glass epoxy substrate)
4.75 to 5.25
V
Block Diagram and Pin Configuration (Top View)
IRIS LEVEL DET OUT IRIS OUT DET CLP IRIS CLP IRIS GC VG OUT PBLK CLP1 W ND VCC2
GND
24
23
22
21
20
19
18
17
16
VG
15
14
13
DET LEVEL
25
CLP CLP1 CLP1
12
CSAGC SL
CLP BLK
AGC CLP 26
11 CSAGC GC
W ND PBLK MODE SW OR SLICE GC
W ND
W ND
AGC OUT 27 OP IN + 28
10 9
CS OUT
W ND
CS CCD GC
PBLK
BLK
SLICE GC
GC
CLP
OP
OP IN - 29 OP OUT 30
AGC CONT
8 7 6
SH XSP3 LPF PBLK CLP BLK CLP1 CLP BLK CLP1 CLP BLK GATE
CS CCD SL
CLP
CLP1
CLP1
31
AGC
MAX
CS CLP
F3 OUT
AGC MAX 32 XSHP XSHP
5 4 3 2 1
F2 OUT
SH
AGC SEL
33 34
SH
SH XSP2
LPF PBLK
F1 OUT
XSHD COM
XSHD
CLP4
CLP4
XSHP
GY OUT
SH
SH
XSHD 35 XSHP SH
COM
SH XSP1
LPF PBLK
DC OUT
CLP4 36
XSH1
37
PG IN
38
DATA IN
39
VCC1
40
XSP3
41
XSP2
42
XSP1
43
GND
44
FSH1
45
F3 CLP
46
F2 CLP
47
F1 CLP
48
XSH2
Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits.
-1-
E90941A78
CXA1390AQ/AR
Pin Description and Standard Pin voltage PIn No. 1 34 35 40 41 42 48 Symbol XSH1 XSHP XSHD XSP3 XSP2 XSP1 XSH2
1k 1 34 35 200 130
(VCC = 5V) Equivalent circuit Description
Voltage
H: 4V and above L: 1V and below
40 41 42 48 200
High speed pulse input pin for S/H (active at L)
2
DC OUT
1.8 to 2.1V
180A
2
DC output pin of f1 to f3 output black level
3 4 5 6 27 7 18 20 26 45 46 47 10
GY OUT
300
F1 OUT F2 OUT F3 OUT AGC OUT CS CLP IRIS CLP DET CLP AGC CLP F3 CLP F2 CLP F1 CLP CS OUT 2.6 to 3.3V 2.0 to 2.6V 1.9 to 2.6V
130
3
Black level 1.8 to 2.1V
360A
4 5 6 27
Signal output pin
7 18 20 26 45 46 47
2.3 to 2.8V 2.0 to 2.6V 2.0 to 2.6V 2.0 to 2.6V 1.7 to 2.2V
300 10
Capacitor connecting pin for clamp
Signal output pin
17
IRIS OUT
1.7 to 2.0V
200A
17 24
Signal output pin Vcc fluctuations effect is minor on DC level
24
DET OUT
1.7 to 2.0V
-2-
CXA1390AQ/AR
PIn No. 8
Symbol
Voltage
Equivalent circuit
Description Level adjustment pin of high luminance detection pin of the input signal Gain adjustment pin of input signal high luminance part
CS CCD SL
9 11 12 21 22 25 31 32
CS CCD GC CSAGC GC CSAGC SL IRIS LEVEL IRIS GC DET LEVEL AGC CONT AGC MAX (Test mode at 0V)
8 9 11 12 21 22 25 31 32 130
Gain adjustment pin of high luminance port after AGC Level adjustment pin of high luminance detection after AGC Adjustment pin of IRIS output weighting (Active at WND = L) Gain adjustment pin of IRIS output Adjustment pin of DET output weighting (Active at WND = L) AGC amplifier gain adjustment pin AGC amplifier MAX gain adjustment pin CLP1 pulse input pin Active at H (OPB clamp) Pre BLK pulse input pin Active at L Window pulse input pin Active at L CLP4 pulse input pin Active at H
13
CLP1
130 13 14
14
P BLK H: 4V and above L: 1V and below
15
WND
130 15 36
36
CLP4
16
VG OUT
2.6 to 3.1V
100A
16
Regulator output pin (Used for the formation of AGC and IRIS loop)
28
OP IN +
28
130
Operation amplifier non inverted input pin
1 to 3.3V 29 OP IN -
130 29
Operation amplifier inverted input pin
-3-
CXA1390AQ/AR
PIn No.
Symbol
Voltage
Equivalent circuit
Description
500A 30
30
OP OUT
H: 4.2V and above L: 1.2V and below
3.6V
Output pin
33
AGC SEL
VCC: Low Gain mode GND: High Gain mode
3.3V
50k 33
AGC amplifier gain selection pin
100A 37 38
37 38
PG IN DATA IN
Black level 2.7 to 3.2V
CCD signal input pin
8.5k 44
44
FSHI
1.4 to 1.8V
130
Adjustment pin for color separation S/H follow up speed (Normally used OPEN)
-4-
CXA1390AQ/AR
Electrical Characteristics Item Current consumption Symbol ID ACON Min. AGC OUT/DATA IN AGC CONT = 1.5V AGC MAX = 5V AGC SEL = 0V AGC OUT/DATA IN AGC CONT = 4.5V AGC MAX = 5V AGC SEL = 0V AGC OUT/DATA IN AGC CONT = 4.5V AGC MAX = 1.5V AGC SEL = 0V AGC OUT (SEL = 5V) /AGC OUT (SEL = 0V) Note 1) Color separation output/AGC OUT (f1, f2, f3) Note 1) -5 -10 -0.5 -10 1.8 GY OUT/AGC OUT IRIS OUT/DATA IN IRIS GC = 5V WND = 5V IRIS OUT/DATA IN IRIS GC = 1.5V WND = 5V Gain Cont Max. ratio (attenuation) IRIS GC = 1.5V IRIS LEVEL = 5V WND = 0V Gain Cont Max. ratio (attenuation) IRIS GC = 1.5V IRIS LEVEL = 1.5V WND = 0V DET OUT/AGC OUT WND = 5V DET OUT/AGC OUT DET LEVEL = 5V WND = 0V Level Max. ratio DET LEVEL = 1.5V WND = 0V -2 -0.5 18 Conditions Min. 32
(Ta = 25C, VCC = 5.0V) Typ. 48 Max. 65 Unit mA
CONT Min.
6
8
dB
CONT Max. AGC Max. Min.
ACON Max.
30
32
dB
MAX Min.
17
20
dB
Gain shift BLK offset Color Gain separation BLK offset DC OUT Gate Gain Gain Cont Max.
GSHI BLK f Gain f BLK DC GY IR Max.
-4 0 0 0 1.95 0 22
-3 +10 +0.5 +10 2.1 +0.5
dB mV dB mV V dB dB
Gain Cont Min. IRIS Window Level Max.
IR Min.
4
8
dB
IRW Max.
-1
0
dB
Window Level Min.
IRW Min.
-14
dB
Gain
DET G DET Max. DET Min.
-1
+0.5
dB
DET
Window Level Max.
-2
-1
+0.5
dB
Window Level Min.
-13
dB
-5-
CXA1390AQ/AR
Item
Symbol
Conditions CSOUT differential/ DATA IN differential CS CCD SL = 4.1V CS CCD GC = 5V PBLK = 0V CSOUT differential/ DATA IN differential CS CCD SL = 4.1V CS CCD GC = 1.5V PBLK = 0V Input conversion slice level CS CCD SL = 1.5V Note 1) Input conversion slice level CS CCD SL = 5V Note 1) CS OUT DATA IN = 0.2Vpp CS AGC GC = 5V CS AGC SL = 4.2V CS CCD GC = 1.5V CS CCD SL = 1.5V Note 2) CS OUT differential/ AGC OUTdifferential CS AGC GC = 1.5V CS AGC SL = 4.2V CS CCD GC = 1.5V CS CCD SL = 1.5V Note 2) AGC OUT conversion CS AGC SL = 1.5V Note 3) AGC OUT conversion CS AGC SL = 5V Note 3) DATA IN = 0.5Vpp CS CCD GC = 0V Note 4) OP IN + = 2.1V OP IN - = 2.0V OP IN + = 2.0V OP IN - = 2.1V At no load
Min.
Typ.
Max.
Unit
Max. Gain
CSC Max.
13
16
dB
Min. Gain CS CCD
CSC Min.
-1
1
dB
Max. SLICE
CSC Max. SL CSC Min. SL
0.7
V
Min. SLICE
40
100
mV
Max. Gain
CSA Max.
0.5
Vpp
CS Min. Gain AGC
CSA Min.
-1
1
dB
Max. SLICE
CSA Max. SL CSA Min. SL
1.2
V
Min. SLICE
0.06
0.1
V
TEST mode
TEST
0.5
Vpp
OPAmp
H level L level
OPH OPL Vg
4.2 0.9 2.6 2.85 1.2 3.1
V V V
Vg OUT
-6-
CXA1390AQ/AR
Note 1)
Indicates the specification
Output signal BLK input 5 0
Note 2) Voltage between DATA IN input black level and the high luminance level determined by CS CCD SL pin voltage.
Black level High luminance level Indicates the specification CS OUT
DATA IN
Note 3) Voltage between the black level at AGC OUT and the high luminance level determined by CS AGC SL pin voltage.
High luminance level AGC OUT Black level Indicates the specification
CS OUT
Note 4) S/H output DATA IN input can be monitored by turning CS CCD GC (Pin 9) to 0V.
-7-
CXA1390AQ/AR
Test Circuit
VCC 5V (3V) (3V) (3V) (3V)
0.1
IRIS LEVEL
0.1
CLP2
10
DET OUT IRIS GC
DET CLP
IRIS CLP
IRIS OUT
VG OUT
PBLK
VCC2
GND
W ND
24
23
22
21
20
19
18
17
16
VG
15
14
13
CLP1
(3V)
DET LEVEL
25
CLP CLP1 CLP1
12
CSAGC SL
(3V )
W ND PBLK
0.1
W ND W ND
CLP BLK
AGC CLP 26
11 CSAGC GC
MODE SW OR
SLICE GC
(3V)
AGC OUT 27 OP IN + 28
10 9
CS OUT
W ND
(2V)
CS CCD GC
(3V)
PBLK
BLK
SLICE
GC
CLP
OP
(2V)
OP IN - 29
CLP
GC
8 7 6
SH XSP3 LPF PBLK CLP BLK CLP1 CLP BLK CLP1 CLP BLK GATE
CS CCD SL
(3V)
MAX
OP OUT 30
(1.5V) AGC CONT
CLP1
CS CLP
CLP1
0.1
F3 OUT
31
AGC
(5V)
AGC MAX 32
5 4 3 2 1
F2 OUT
XSHP
SH
(0V)
AGC SEL
33 34
XSHP
SH
SH XSP2 SH XSP1
LPF PBLK
F1 OUT
XSHD
XSHD COM
CLP4
CLP4
XSHP
GY OUT
SH
SH
XSHD 35
COM
LPF PBLK
DC OUT
CLP4 36
SH
CLP4
XSHP
XSH1
37
PG IN
38
DATA IN
39
VCC1
40
XSP3
41
XSP2
42
XSP1
43
GND
44
FSH1
45
F3 CLP
46
F2 CLP
47
F1 CLP
48
XSH2
0.1 0.1 IN 10 VCC 5V 0.1 0.1 0.1
Note 1) Capacitor unit value at F. Note 2) Voltage in parentheses are those not specified in the Electrical Characteristics Test Conditions. Note 3) indicates a test pin. (For both AC and DC)
-8-
CXA1390AQ/AR
Timing Diagram for Testing
Equivalent to black DATA IN input Differs with every test
5V CLP 1
2sec
1H
0 2sec
5V CLP 4
0
Output waveform AGC OUT IRIS OUT F1 to F3 OUT GY OUT DET OUT CS OUT
Output signal level
-9-
CXA1390AQ/AR
Standard Control Characteristics (VCC = 5V, Ta = 25C)
AGC amplifier gain control characteristics
dB (AGC Max. = 5V) 30 30 dB (AGC CONT = 5V)
AGC maximum control characteristics
25
20
20
15
10
10
5
0
1
2
3
4
5
V
5
0
1
2
3
4
5
V
AGC CONT voltage
AGC maximum voltage
IRIS gain control characteristics
dB dB
IRIS WINDOW control characteristics (Weighting characteristics)
(WND = 0V) Gain control characteristics when IRIS LEVEL=5V is set at 0dB 0
25
20 -5 15 -10 10 -15 5 -20 0 0 1 2 3 4 5 V 1 2 3 4 5 V
IRIS GC voltage
IRIS LEVEL voltage
DET WINDOW control characteristics (Weighting characteristics)
dB (WND = 0V) Gain control characteristics when DET LEVEL = 5V is set at 0dB 0
-5
-10
-15
-20 1 2 3 4 DET LEVEL voltage 5 V
- 10 -
CXA1390AQ/AR
CS CCD gain control characteristics
dB V
CS CCD slice control characteristics
(High luminance detection level control) Input conversion value
Note 1-b
20 Note 1-a
0
15
0.2
0.4 10 0.6 5 0.8 0 0 1 2 3 4 5 V CS CCD GC voltage
1.0
0
1
2
3
4
5
V
CS CCD SL voltage
CS AGC gain control characteristics
dB V
CS AGC slice control characteristics
Note 2-b
20
1.6 Note 2-a 1.2
15
0.8 10 0.4 5 0 0 1 2 3 4 5 V 1 2 3 4 5 V CS AGC GC voltage CS AGC SL voltage (High luminance detection level control after AGC) Input conversion value
Note 1-a, 1-b
(2) DATA IN SLICE (1) CS CCD SL CS CCD GC GCA (3) CS OUT
Note 2-a, 2-b
COLOR SEPARATION AGC (1) CS AGC SL Detection level CS AGC GC SLICE (2) CS OUT GCA (3)
(1) Detection level (2)
Black level Note 1-b Voltage indicated at CS CCD slice control characteristics Note 1-a Characteristics indicated at CS CCD gain control characteristics =ratio of 3 and 2 (dB)
(1) Black level (2)
Note 2-b Voltage indicated at CS AGC slice control characteristics
(3)
(3)
Note 2-a Characteristics indicated at CS AGC slice control characteristics =ratio of 3 and 2 (dB)
- 11 -
CXA1390AQ/AR
Supply voltage Characteristics Standard Design Documentation (Ta = 25C)
AGC amplifier gain control characteristics
dB 5.25V 30 (AGC Max. = VCC) 4.75V 25 4.75V 20 5V (AGC CONT = VCC) 30 dB 5.25V 5V
AGC maximum control characteristics
20
15
10
10
5 0 1 2 3 4 5 AGC CONT voltage
(x VCC ) 5
5 0 1 2 3 4 5 AGC maximum voltage
(x VCC ) 5
IRIS gain control characteristics
dB dB
IRIS WINDOW control characeristics (Weighting characteristics)
WND = 0V Gain control characteristics when IRIS LEVEL = Vcc is set at 0dB 0 5.25V 5V
25
20
5.25V 5V 4.75V
-5 15 -10 10 -15 5 -20 0 0 1 2 3 4 5 IRIS GC volage x VCC 5 1 2 3 4 5 (x VCC ) 5 4.75V
IRIS LEVEL voltage
DET WINDOW control (Weighting characteristics)
dB WND=0V Gain control characteristics when DET LEVEL=Vcc is set at 0dB 0 5.25V 4.75V 5V
-5
-10
-15
-20 1 2 3 4 DET LEVEL voltage 5 (x VCC ) 5
- 12 -
CXA1390AQ/AR
CS CCD gain control characteristics
dB Note 1-a 20 5.25V 5V 4.75V 0 V
CS CCD slice control characteristics
(High luminance detection level control) Input conversion value Note 1-b 5.25V 5V
15
0.2 4.75V
0.4 10 0.6 5 0.8 0 0 1 2 3 4 5 (x CS CCD GC voltage
VCC ) 5
1.0 0 1 2 3 4 5 (x CS CCD SL voltage
VCC ) 5
CS AGC gain control characteristics
dB Note 2-a 20 5.25V 5V 15 4.75V 1.2 1.6 V
CS AGC slice control characteristics
Note 2-b
0.8 10 0.4 5 0 0 1 2 3 4 5 CS AGC GC voltage (x VCC ) 5 1 2 3 4 (High luminance detection level control after AGC) Input conversion value
4.75V 5V
5.25V
5
CS AGC SL voltage
(x VCC ) 5
Note 1-a, 1-b
(2) DATA IN SLICE (1) CS CCD SL CS CCD GC GCA (3) CS OUT
Note 2-a, 2-b
COLOR SEPARATION SLICE
(2) CS OUT GCA (3) CS AGC SL CS AGC GC
AGC (1) Detection level
(1) Detection level (2)
Black level Note 1-b Voltage indicated at CS CCD slice control characteristics Note 1-a Characteristics indicated at CS CCD gain control characteristics =ratio of 3 and 2 (dB)
(1) Black level (2)
Note 2-b Voltage indicated at CS AGC slice control characteristics
(3)
(3)
Note 2-a Characteristics indicated at CS AGC slice control characteristics =ratio of 3 and 2 (dB)
- 13 -
CXA1390AQ/AR
Standard Design Documentation Temperature Characteristics (VCC = 5V)
AGC amplifier gain control characteristics
dB -20C 30 (AGC Max. = VCC) 25C 75C 25 75C 30 (AGC CONT = VCC) dB -20C 25C
AGC maximum control characteristics
20
20
15
10
10
5 0 1 2 3 4 5 V AGC CONT voltage
5 0 1 2 3 4 5 V AGC maximum voltage
IRIS gain control characteristics
dB dB
IRIS WINDOW control characteristics (Weighting characteristics)
(WND = 0V) Gain control characteristics when IRIS LEVEL = VCC, Ta=25C is set at 0dB. -20C -5 75C
25
20
-20C 25C 75C
0
25C
15 -10 10 -15 5 -20 0 0 1 2 3 4 5 V 1 2 3 4 5 V IRIS GC voltage IRIS LEVEL voltage
DET WINDOW control (Weighting characteristics)
dB (WND = 0V) Gain control characteristics when DET LEVEL = VCC, Ta = 25C is set at 0dB. -20C 75C -5 25C
0
-10
-15
-20 1 2 3 4 DET LEVEL voltage 5 V
- 14 -
CXA1390AQ/AR
CS CCD gain control characteristics
dB Note 1-a 20 -20C 15 25C 75C 0.2 0 V
CS CCD slice control characteristics
(High luminance detection level control) Input conversion value
Note 1-b -20C 25C 75C
0.4 10 0.6 5 0.8 0 0 1 2 3 4 5 V CS CCD GC voltage
1.0 0 1 2 3 4 5 V CS CCD SL voltage
CS AGC gain control characteristics
dB Note 2-a -20C 20 25C 75C 15 1.6 V
CS AGC slice control characteristics
Note 2-b
1.2
0.8 10 0.4 5 0 0 1 2 3 4 5 V 1 2 3 4 5 V CS AGC GC voltage CS AGC SL voltage (High luminance detection level control after AGC) Input conversion value 75C 25C -20C
Note 1-a, 1-b
(2) DATA IN SLICE (1) CS CCD SL CS CCD GC GCA (3) CS OUT
Note 2-a, 2-b
COLOR SEPARATION AGC (1) CS AGC SL Detection level SLICE
(2) CS OUT GCA (3) CS AGC GC
(1) Detection level (2)
Black level Note 1-b Voltage indicated at CS CCD slice control characteristics Note 1-a Characteristics indicated at CS CCD gain control characteristics =ratio of 3 and 2 (dB)
(1) Black level (2)
Note 2-b Voltage indicated at CS AGC slice control characteristics
(3)
(3)
Note 2-a Characteristics indicated at CS AGC slice control characteristics =ratio of 3 and 2 (dB)
- 15 -
CXA1390 Series System Diagram (The title insertion function can be removed by doing away with CXA1393AN)
W/B CONTROLLER IHDL IHDL IHDL
CCD
DL
DETECTOR
51 47 41 34 39 33
50 44
49 48 45 43 42
46
40
38 37
36 35
YOCLP S1-IN
S2-IN
R-MIX
B-CLP
G-CLP
B-MTX
R-CLP
B-GAIN
B-CONT
R-CONT
R-GAIN
DLC1-IN
CLP4
C1-GAIN
DLD
XSHD
XSHP
DLCO-OUT
MPX2-CLP
MPX1-CLP
SHPLEVEL DLE
OPIN-N
OPIN-P
OP-OUT
AGC-SEL
AGC-OUT
AGC-MAX
AGC-CLP DETLEVEL
SHP-CLP1
AGC-CONT
39 VCC1 39 YH-CLP 40 YH-IN 41 YL-YH CLP 42 YL-YH IN 43 AGND 44 CLP4 45 CLP2 46 B-LEVEL 47 B-Y IN 48 B-Y 56 DLY2-IN
IRIS-GC 22 WB-R 28 CGAM-CONT 27 CXA1391 Q/R GND 26 YL-OUT 25 CS-OUT 24 VCS-GAIN 23 R-Y HUE 22 B-Y HUE 21 R-Y 20 OUT
55 DLY1-IN
WB-G 29
FADER-MODE
SYNC-LEVEL SETUP
5V
38 DATA-IN 38 NOISE-SLICE
DET- 24 OUT VCC2 23 5V
54 Y1-GAIN 37 YTBLK
SHP-CLP2
SHP-OUT
Y-LEVEL
WB-B 30
FADER-SIG
37 PG-IN
OUT 53 DLY1-OUT
C- 32 SLICE WB-DC 31
SYNC
52 DLY0-
C LEVEL
36 34 29 33 28 31 30
35 36 32
ID
34
33
32
31 30
29
28
27
26
25
35
27
26
25
WC 24
SETUP- 23 CLP V-OUT 22 VIDEO-OUT 21 CHROMA-OUT 20
Y Vid C
40 XSP3 57 Y2-GAIN 58 GND 59 60 LPF-ADJ2
IRIS-LEVEL 21
41 XSP2
DET-CLP 20
42 XSP1
CXA1390AQ/AR LPF-ADJ1
GND 19
CXA1392Q/R
DGND 19 C-IN 18 AVCC 17 C-OUT 16 CS-Y 15 CS-AGC 14 4FSC LALT BPF 5V
43 GND
IRIS-CLP 18
44 FSHI
IRIS-OUT 17 5V
62 VCC 63 YGAM61 LPF-ADJ3
45 F3-CLP
VG-OUT 16
46 F2-CLP
WND 15 CONT YH-OUT1 YH-OUT2 TP CLP4 CLP2 VAP-OUT VAP-CLP CS-CLP CS-IN R-Y GAIN B-Y GAIN B-Y OUT
47 F1-CLP 64 YH-IN
PBLK 14
48 XSH2
CLP1 13
NC
NC
FSC-OUT
BFG
BF
R-Y IN
R-Y CLP
XSH1
DC-OUT
GY-OUT
F1-OUT
F2-OUT
F3-OUT
CS-CLP
CS-CCD-SL
CS-CCD-GC
CS-OUT
CS-AGC-GC
CS-AGCSL
YHCLP DLYH-IN
DLYH-CLP
DLYH-OUT
DLYH-GAIN
VAP-GAIN
CLP4
DB-IN
DR-IN
GND
CB-IN
CG-IN
XSH1 XSH2
CLP1
ID PBLK
YG-IN
YR-IN
YB-IN
YT-GC
DR-OUT
CT-BLK DB-OUT
DY-OUT
YT-BLK
DY-CLP
DY-IN
XSP1
XSP2 WND CONTROLLER FOR TITLER YR YG YB BLK BF SYNC LALT 4fSC CR CG CB
13
14
15
16
17 18
19
VCC
20 21
22 23
24
TG SG
CLP4
XSHD
XSHP
BFG
CT-GC
CLP2
HYSCONT TH-CONT COMP-IN COMPOUT
CXA1393AN/AM
CR-IN
- 16 -
1 2 3 7 11 16 4 8 10 14 17 15 5 12 6 9 13 18 19
1
2
3
4
5
6
VAP-SLICE
DVCC
7
8
9
10
11
12
1
2
3
4
5
6
7
8
9
10
11
5V
5V LPF
DL LPF IHDL
LPF DL
12 11 10 9 8 7 6 5 4 3 2 1
CBLK CTBLK CLP
MODE 13
12
CXA1390AQ/AR
CXA1390AQ/AR
Package Outline CXA1390AQ
Unit: mm
48PIN QFP (PLASTIC)
15.3 0.4 + 0.4 12.0 - 0.1 + 0.1 0.15 - 0.05
36
25
0.15
37
24
48
13
+ 0.2 0.1 - 0.1
1 + 0.15 0.3 - 0.1
12
0.8
0.12 M
+ 0.35 2.2 - 0.15
PACKAGE STRUCTURE
PACKAGE MATERIAL SONY CODE EIAJ CODE JEDEC CODE QFP-48P-L04 QFP048-P-1212-B LEAD TREATMENT LEAD MATERIAL PACKAGE WEIGHT EPOXY RESIN SOLDER / PALLADIUM PLATING COPPER / 42 ALLOY 0.7g
CXA1390AR
48PIN LQFP (PLASTIC)
9.0 0.2 36 37 7.0 0.1 25 24
(8.0)
A 48 1 0.5 0.08 + 0.08 0.18 - 0.03 0.1 0.1 + 0.2 1.5 - 0.1 12 13
(0.22)
+ 0.05 0.127 - 0.02 0.1
0 to 10
0.5 0.2
NOTE: Dimension "" does not include mold protrusion. DETAIL A
PACKAGE STRUCTURE
PACKAGE MATERIAL SONY CODE EIAJ CODE JEDEC CODE LQFP-48P-L01 QFP048-P-0707-A LEAD TREATMENT LEAD MATERIAL PACKAGE WEIGHT EPOXY / PHENOL RESIN SOLDER PLATING 42 ALLOY
0.2g
- 17 -
0.5 0.2
0.9 0.2
13.5

▲Up To Search▲

Price & Availability of CXA1390AQ

	To Download CXA1390AQ Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .